What Is MST-01?
MST-01 is a liquid ionic soil stabilizer used together with 42.5 Portland cement to solidify on-site soil into a dense, water-resistant subgrade or base layer. Contractors mix MST-01 and cement into the existing compacted soil matrix, compact it, and cure for 7–14 days, so there is no need to haul in crushed stone. It suits clay, silty clay, silt, sand, coal gangue and construction waste.
Typical dosage: 0.5-1.0 L per m³ of compacted soil, diluted with water. Cement dosage ranges 5%-15% by weight of compacted soil. When using MST-01 as an additive, cement content can typically be reduced from 12-15 % down to 7-10 % to achieve equivalent 7-day compressive strength, depending on soil type.
MST-01 does not replace cement entirely. It is an additive that enables reduced cement dosage compared with cement-only stabilization. Compared with cement- or lime-stabilized crushed stone, it enables local soil reuse and cuts external-material hauling costs. Cost savings are heavily dependent on aggregate hauling distance. Savings become more significant where quarry aggregates must be transported over long distances.
Product Specifications
| Test Item | Technical Index | Test Result |
| Appearance | Translucent Liquid | Translucent Liquid |
| Solid Content(%) | ≥ 20 | 20.72 |
| PH Value( 20 ℃ ) | 6-8 | 7.01 |
| Density(20℃,g/cm³) | 0.9-1.1 | 1.05 |
How it works?
The ionic MST-01 soil stabilizer functions in three key stages:
- Charge neutralization: Lowers zeta potential on soil-colloid surfaces to reduce electrostatic repulsion between soil particles.
- Water-state transformation: Converts a large amount of free water inside soil into crystallized bound water via physical-chemical interactions.
- Particle consolidation together with cement hydration: Through a series of physical-chemical reactions, soil particles coagulate, electrolyte concentration rises and volume expansion fills soil pores.
Under mechanical compaction, soil forms an integrated continuous structure. It greatly improves compaction degree, compressive strength, resilience modulus, shear strength and anti-permeability of soil, meeting technical requirements for road subgrade and other earthworks.

Key Advantages
- Low-cost local-material solution: Savings depend mainly on how far aggregate must be hauled. Higher cost benefit is achieved in locations with long haul distances for crushed-stone aggregates. On-site soil reuse eliminates aggregate procurement and long-distance transportation expenditures.
- Fast Construction: After compaction, close the section to traffic immediately. Light-weight construction vehicles may pass after 7 days; normal traffic opens after 14 days of curing, depending on ambient temperature and design strength requirements. All mixing, leveling and compaction operations shall be finished within 4 hours after cement addition, before cement initial setting completes.
- Eco-friendly performance: Heavy-metal leaching tested per GB/T 5085.3-2007 by Hengxin Material Testing Laboratory, Report No. HX-2025-0413, Apr 13, 2025; all test values are below regulatory limit values. SDS and full test reports are available upon request.
- Strong Integrity: Forms a dense monolithic structure, greatly enhancing bearing capacity and service life of the stabilized base layer.
- Helps reduce reflective cracking: MST-01 ionic soil stabilizer helps reduce shrinkage cracking compared with cement-only stabilization under identical cement-dosage conditions.
- Water & Corrosion Resistance: The reacted stabilized soil matrix delivers hydrophobic performance, ensuring structural integrity against water damage and chemical corrosion.
- Low Settlement: Progressive strength gain at later ages improves bearing capacity. Uniform stress distribution minimizes uneven settlement risk.
- Durable performance: The stabilized layer shows good resistance to bending, pulling, seepage, frost heave, and mud-pumping failure modes. It balances rigidity and flexibility for long-term field performance.

Application Scenarios
MST-01 ionic soil stabilizer is applicable to many types of soils, such as clay, silty clay, silt, sand, slag, coal gangue, construction waste, solid waste and slurry.
Not suitable: black cotton soil (highly expansive clay with strong swell-shrink behaviour). For highly-expansive soils, top-soil replacement is recommended; please consult our engineering team for custom proposals. Pre-lab testing is recommended for soils with high organic content or high sulfate content.
According to different soil conditions and design requirements, we can adjust the material ratio to develop customized solidification schemes.
-Subgrade construction
-Ground hardening
-Rammed earth wall, earth-plastered wall
-Production of unfired bricks and stone
-look bricks
-Slope protection, solidification of anti-seepage sites
-Soft soil / soft foundation, and foundation pit backfill solidification;
When applied on planting-soil slopes, it provides temporary slope stabilization for vegetation establishment.

What is the construction process?
- Construction Section Surveying: Conduct survey by coordinate method using a total station or equivalent survey instruments.
- Soil Preparation and Leveling: Use excavators to excavate the road to the required design depth in 20-30 cm lifts. Till the soil with a rotary tiller. Remove big stones during excavation until it becomes fine soil.
- Spreading & Mixing of Cement: Spread cement evenly within marked grids according to the mix proportion. Mix with rotary tiller or road mixer and remove all debris. Lime is not the recommended binder for this product; special formula is required if lime shall be adopted.
- Mixing and Spraying: Mix the stabilizer with water at pre-defined dilution ratio depend on the soil moisture content. Spray it onto the soil by water cart. Control the spraying frequency to ensure even spraying.
- Mixing soil: Use road mixer or tractor with rotary tiller to mix liquid and soil thoroughly.
- Compaction and Rolling: Use a 20-ton or heavier vibratory roller to compact the road, then level with a grader. All compaction work must be completed within 4 hours after cement spreading.
- Curing and Traffic Control: Once compaction of each stabilized-soil section is finished, close traffic immediately. Cover with geotextile and spray water for curing, keep the surface wet all the time. Cure for 7-14 days depending on air temperature.
- Spraying sealing layer: Spray diluted sealing stabilizer on surface based on road condition.

Get in Touch
If you want to know more, get in touch with us now!
We offer technical support, project solutions, quotation and samples for ionic water-resistant, self-repairing MST-01 soil stabilizer.Feel free to reach out to us for this eco-friendly soil stabilizer!
Hot Tags: ionic soil stabilizer, China ionic soil stabilizer manufacturers, suppliers, factory, ground stabilizer, lime soil stabilization, mechanical soil stabilization, Polymer Road Stabilizer, Road Soil Stabilizer, soil stabilization road construction







